swedge程序说明翻译
下里巴人@sl
2006年05月10日 11:33:05
只看楼主

Support TutorialBolts and / or shotcrete may be added to an SWEDGEmodel, to evaluate the effect of support on wedge tability.In this tutorial, we will first add bolts to a wedge model,and then shotcrete, and discuss how each is implemented in the SWEDGE analysis.Let’s start with a new (Deterministic) file for the purposes

Support Tutorial
Bolts and / or shotcrete may be added to an SWEDGEmodel, to evaluate the effect of support on wedge tability.In this tutorial, we will first add bolts to a wedge model,and then shotcrete, and discuss how each is implemented in the SWEDGE analysis.Let’s start with a new (Deterministic) file for the purposes
of the following demonstration.
Select: File →New
锚杆和喷砼可能在SWEDGE模型中加入,以分析支护对块体稳定影响,这里,我们首先在模型中添加锚杆,然后是喷砼,讨论各自在模型分析中的作用,我们下来开始一个新文件以实现这一目标。
Adding Bolts
Bolts are added individually to a wedge model, with the Add Bolt option in the toolbar or the Support menu.
Select: Support →Add Bolt
在模型中,锚杆是分别加入的,使用工具条或Support菜单中的锚杆选项来实现。
1. Move the cursor into the Top or Front orthogonal views.
2. Notice that the cursor changes to an “arrow / rockbolt”icon.
3. As you move the cursor over the wedge, notice that the “rockbolt” and “arrow” now line up – this indicatesthat you may add the bolt to the wedge.
4. Click the LEFT mouse button at a point on the wedge where you want the bolt installed.
5. The bolt will initially be installed NORMAL to the face of the wedge on which you clicked (ie. normal to the Upper or Face slope), however you can modify the orientation using the Bolt Properties dialog which you will see in the middle of the screen.
1.移动光标到Top or Front视图;
2.注意光标变成一个“箭头/锚杆)图标
3.当你移动光标,“rockbolt” and “arrow”会line up,表明可以添加。
4.点击鼠标左键你想施加的点
5.锚杆将初步加在NORMAL模型表面,使用屏幕中的锚杆特性修改对话框可以修改方位。
免费打赏
下里巴人@sl
2006年05月10日 11:33:32
2楼
6. To optimize the bolt orientation to provide maximum safety factor, you can select the Optimize button in
the Bolt Properties dialog (this is optional).
7. Notice the effect on the safety factor. When a bolt is initially added, the safety factor is automatically recomputed.(If you used the default bolt Capacity of 20 tonnes, the effect on the safety factor will be very
small in this case, since the default wedge for a new file is a 16000 tonne wedge.)
8. Note the following about the Bolt Properties dialog:If you modify the Capacity, Trend or Plunge with
the “arrow” buttons at the right of the dialog, the Safety Factor is immediately recalculated.Alternatively, values can be typed in to the dialog. In this case, the user must select the Apply button to re-calculate the Safety Factor. Support Tutorial 65,As the bolt Trend and Plunge are changed, you will see the orientation of the bolt updated on the screen.
9. When you are satisfied with the bolt orientation,length and capacity, select OK to add the bolt to the
model.
10. If you are not happy with the location of the bolt, or do not want to add the bolt to the model, select
Cancel, and the bolt will be deleted.
11. Repeat the above steps to add a few more bolts to the model. Try using larger bolt capacities. Note the effect on safety factor.
Note:
Bolts can NOT be added in the Perspective View.Bolts can be added in the Side View, but this is not
recommended, as correct placement may be difficult or impossible.

6.通过选择锚杆特性对话框的优化按钮,可以提供最大安全系数的锚杆方位。
7.注意其对安全系数的影响,当锚杆初步施加,安全系数即自动计算(如果你使用默认锚杆20 tonnes,对安全系数的影响将非常小,因为一个新文件的默认块体是一个16000 tonne 块体。
8.注意以下锚杆特性对话框:如果你使用右边对话框的箭头修改了Capacity、趋势或Plunge,安全系数会立即重算,替代值在对话框显示。这时,使用者必须使用应用按钮重新计算安全系数,因为锚杆趋势和Plunge被修改,你将看到屏幕上的锚杆方位更新。
9当你对锚杆定位、长度和capacity满意,选择OK添加锚杆模型。
10否则,按Cancel,锚杆将被删除。
11重复上述步骤添加多个锚杆,使用大锚杆capacities,注意对安全系数的影响。

回复
jts3
2006年09月13日 19:27:20
3楼
我看还行 帮忙顶一下
回复
lhf711223
2009年11月18日 11:21:44
4楼
要是有完整的说明翻译就好了!:victory:
回复
red1989
2013年01月24日 17:15:14
5楼
内容还可以,但太少了,能持续上传就好了
回复

相关推荐

APP内打开